Multifunctional Surface Treatment against Imperfections and Halide Segregation in Wide-Band Gap Perovskite Solar Cells.

Mixed-halide wide-band gap perovskites (WBPs) still suffer from losses due to imperfections within the absorber and the segregation of halide ions under external stimuli. Herein, we design a multifunctional passivator (MFP) by mixing bromide salt, formamidinium bromide (FABr) with a p-type self-assembled monolayer (SAM) to target the nonradiative recombination pathways. Photoluminescence measurement shows considerable suppression of nonradiative recombination rates after treatment with FABr. However, WBPs still remained susceptible to halide segregation for which the addition of 25% p-type SAM was effective to decelerate segregation. It is observed that FABr can act as a passivating agent of the donor impurities, shifting the Fermi-level (Ef) toward the mid-band gap, while p-type SAM could cause an overweight of Ef toward the valence band. Favorable band bending at the interface could prevent the funneling of carriers toward I-rich clusters. Instead, charge carriers funnel toward an integrated SAM, preventing the accumulation of polaron-induced strain on the lattice. Consequently, n-i-p structured devices with an optimal MFP treatment show an average open-circuit voltage (VOC) increase of about 20 mV and fill factor (FF) increase by 4% compared with the control samples. The unencapsulated devices retained 95% of their initial performance when stored at room temperature under 40% relative humidity for 2800 h.

Thermal Disorder-Induced Strain and Carrier Localization Activate Reverse Halide Segregation.

The reversal of halide ions is studied under various conditions. However, the underlying mechanism of heat-induced reversal remains unclear. This work finds that dynamic disorder-induced localization of self-trapped polarons and thermal disorder-induced strain (TDIS) can be co-acting drivers of reverse segregation. Localization of polarons results in an order of magnitude decrease in excess carrier density (polaron population), causing a reduced impact of the light-induced strain (LIS - responsible for segregation) on the perovskite framework. Meanwhile, exposing the lattice to TDIS exceeding the LIS can eliminate the photoexcitation-induced strain gradient, as thermal fluctuations of the lattice can mask the LIS strain. Under continuous 0.1 W cm⁻2 illumination (upon segregation), the strain disorder is estimated to be 0.14%, while at 80 °C under dark conditions, the strain is 0.23%. However, in situ heating of the segregated film to 80 °C under continuous illumination (upon reversal) increases the total strain disorder to 0.25%, where TDIS is likely to have a dominant contribution. Therefore, the contribution of entropy to the system's free energy is likely to dominate, respectively. Various temperature-dependent in situ measurements and simulations further support the results. These findings highlight the importance of strain homogenization for designing stable perovskites under real-world operating conditions.

Anomalous Structural Evolution and Glassy Lattice in Mixed-Halide Hybrid Perovskites.

Hybrid halide perovskites have emerged as highly promising photovoltaic materials because of their exceptional optoelectronic properties, which are often optimized via compositional engineering like mixing halides. It is well established that hybrid perovskites undergo a series of structural phase transitions as temperature varies. In this work, the authors find that phase transitions are substantially suppressed in mixed-halide hybrid perovskite single crystals of MAPbI3-x Brx (MA = CH3 NH3 + and x = 1 or 2) using a complementary suite of diffraction and spectroscopic techniques. Furthermore, as a general behavior, multiple crystallographic phases coexist in mixed-halide perovskites over a wide temperature range, and a slightly distorted monoclinic phase, hitherto unreported for hybrid perovskites, is dominant at temperatures above 100 K. The anomalous structural evolution is correlated with the glassy behavior of organic cations and optical phonons in mixed-halide perovskites. This work demonstrates the complex interplay between composition engineering and lattice dynamics in hybrid perovskites, shedding new light on their unique properties.

Homologous Bromides Treatment for Improving the Open-Circuit Voltage of Perovskite Solar Cells.

The power conversion efficiency (PCE) of solution-processed organic-inorganic mixed halide perovskite solar cells has achieved rapid improvement. However, it is imperative to minimize the voltage deficit (Woc  = Eg /q - Voc ) for their PCE to approach the theoretical limit. Herein, the strategy of depositing homologous bromide salts on the perovskite surface to achieve a surface and bulk passivation for the fabrication of solar cells with high open-circuit voltage is reported. Distinct from the conclusions given by previous works, that homologous bromides such as FABr only react with PbI2 to form a large-bandgap perovskite layer on top of the original perovskite, this work shows that the bromide also penetrates the perovskite film and passivates the perovskite in the bulk. This is confirmed by the small-bandgap enlargement observed by absorbance and photoluminescence, and the bromide element ratio increasing in the bulk by time-of-flight secondary-ion mass spectrometry and depth-resolved X-ray photoelectron spectroscopy. Furthermore, a clear suppression of non-radiative recombination is confirmed by a variety of characterization methods. This work provides a simple and universal way to reduce the Woc of single-junction perovskite solar cells and it will also shed light on developing other high-performance optoelectronic devices, including perovskite-based tandems and light-emitting diodes.